(1. 西南科技大學 環境與資源學院，綿陽 621010；
2. 中鋼集團馬鞍山礦山研究總院股份有限公司，馬鞍山 243000；
3. 西南科技大學 土木工程與建筑學院，綿陽 621010)
摘 要: 以鋰輝石浮選尾礦為主要原料，黏土礦物為黏結材料，輔以少量羧甲基纖維素鈉提高其生坯強度，通過過氧化氫發泡造孔制備出多孔陶瓷材料。通過正交試驗探究各因素對試樣各方面性能的影響并用SPSS軟件對其進行回歸分析。最后結合XRF、XRD、SEM、TG-DSC熱分析和光學顯微鏡觀察對多孔陶瓷化學組成、物相組成、微觀形貌及燒結過程進行分析。結果表明：高嶺土較鈉基膨潤土更適合作為多孔陶瓷黏結材料，對其物理性能影響最大的兩個因素為燒結溫度和黏結劑質量分數，其最優燒結溫度和高嶺土質量分數分別為1150 ℃和10%，此時抗折強度、抗壓強度、顯氣孔率和吸水率分別為2.46MPa、4.93MPa、52.48%和44.96%。高溫下長石熔融產生的液相及傳質作用的增強應為多孔陶瓷顆粒間發生結合的主要原因。二元線性回歸方程擬合結果良好，所制多孔陶瓷氣孔率高、吸水率高，在過濾材料、吸附材料、載體和保水磚等領域具有一定的應用潛力。
關鍵字: 鋰輝石；浮選尾礦；多孔陶瓷；黏結材料；多元線性回歸
（1. School of Environment and Resources, Southwest University of Science and Technology, Mianyang 621010, China;
2. Sinosteel Ma''anshan General Institute of Mining Research Co., Led., Ma''anshan 243000, China;
3. School of Civil Engineering and Architecture, Southwest University of Science and Technology, Sichuan 621010, China）
Abstract:With spodumene flotation tailings as the main raw material, clay minerals as bonding materials, supplemented with a small amount of sodium carboxymethyl cellulose to improve the strength of sample, porous ceramic materials were prepared by hydrogen peroxide foaming. The effects of various factors on the properties of the samples were investigated by orthogonal test, and the regression analysis was carried out by SPSS software. Finally, the chemical composition, phase composition, microstructure and sintering process of porous ceramics were analyzed by XRD, SEM, TG-DSC and optical microscope. The results show that kaolin is more suitable for porous ceramic bonding material than Na-bentonite, and the two factors that have the greatest influence on its physical properties are sintering temperature and binder mass ratio. The optimum sintering temperature and kaolin mass fraction are 1150 ℃ and 10%, respectively. The flexural strength, compressive strength, apparent porosity and water absorption are 2.46 MPa, 4.93 MPa, 52.48% and 44.96%, respectively. The enhancement of liquid phase and mass transfer caused by feldspar softening at high temperature should be the main reason for the combination of porous ceramic particles. The results of binary linear regression equation fitting are good. The porous ceramics have high porosity and high water absorption. It has a certain application potential in filtration materials, adsorption materials, carriers and water retaining bricks.
Key words: spodumene; flotation tailings; porous ceramics; bonding materials; multiple linear regression
