(哈爾濱理工大學 機械動力工程學院，哈爾濱 150080)
摘 要: 為了研究Inconel625高溫合金在較高溫度和應變率變化范圍內的熱變形行為，采用CSS電子萬能試驗機和分離式霍普金森壓桿試驗裝置對Inconel625高溫合金進行準靜態試驗和霍普金森壓桿試驗，在溫度為20~800 ℃、應變率為0.001~8000 s-1范圍內得到Inconel625高溫合金的真實應力—應變曲線。結果表明：隨著溫度的升高，Inconel625高溫合金的流動應力與屈服應力并不單一地隨應變率增大而增大，同一溫度條件下，隨著應變率的增加，Inconel625高溫合金的真實應力先增大后減小(分界線是應變率為6000 s-1)；同一應變率條件下，Inconel625高溫合金的真實應力隨著溫度的升高而減小。基于Johnson-Cook模型對其真實應力-應變曲線進行擬合分析，經過計算得到模型的預測值與實驗值的相關性和絕對誤差，并進一步改進Inconel625高溫合金的Johnson-Cook本構模型，使模型能夠更好地反映Inconel625高溫合金在較高溫度和應變率變化范圍內的熱變形規律。
關鍵字: Inconel 625高溫合金；Johnson-Cook本構模型；應變；熱變形
（School of Mechanical Engineering, Harbin University of Science and Technology, Harbin 150080, China）
Abstract:In order to study the thermal deformation behavior of Inconel625 superalloy at high temperature and strain rate range, the quasi-static test and Hopkinson pressure bar test of Inconel625 superalloy were carried out by using CSS electronic universal testing machine and split type pressure bar test device. The true stress-strain curves of Inconel625 superalloy were obtained in the range of 20-800 ℃ centigrade and strain rate of 0.001-8000 s-1. The experimental results show that the low stress and yield stress of Inconel625 superalloy do not increase with the increase of strain rate. Under the same temperature, the true stress of Inconel625 superalloy increases first and then decreases with the increase of strain rate (the dividing line is strain rate of 6000 s-1). While under the same strain rate, the true stress of Inconel625 superalloy decreases with the increase of temperature. Based on the Johnson-Cook model, the true stress-strain curves are fitted and analyzed. The correlation coefficient and the absolute error between the predicted value and the experimental value are obtained by calculation. By improving the Johnson-Cook constitutive model of Inconel625 superalloy, the model can be used to characterize the themal deformation of Inconel625 superalloy at high temperature and strain rate range.
Key words: Inconel625 superalloy; Johnson-Cook constitutive model; strain; thermal deformation
