(1. 昆明理工大學 材料科學與工程學院，昆明 650093；
2. 昆明理工大學 分析測試研究中心，昆明 650093)
摘 要: 采用Gleeble-1500材料熱/力模擬機，對應變誘導熔化激活法(SIMA)制備的不同原始半固態組織的ZCuSn10銅合金進行單向壓縮實驗。研究預變形量和壓縮變形條件對半固態坯料真應力-應變曲線及其組織的影響，并結合ZCuSn10銅合金壓縮后的宏觀形貌和顯微組織對液相的流動規律進行分析。結果表明：隨著預變形量和變形溫度的增加，流變應力降低。變形溫度對半固態ZCuSn10銅合金壓縮變形峰值應力影響較大，對穩態應力影響較小。與固態金屬壓縮變形相同，半固態ZCuSn10銅合金在半固態溫度區間壓縮變形時，存在3個典型壓縮變形區域，即難變形區(Ⅰ區)、大變形區(Ⅱ區)、自由變形區(Ⅲ區)，Ⅰ、Ⅱ、Ⅲ區的液相率分別為15.23%、5.31%、20.12%。各個變形區之間發生了液相流動，小部分難變形區內的液相流到大變形區，大部分大變形區內的液相流到自由變形區。
關鍵字: ZCuSn10銅合金；半固態；單向壓縮；變形行為
（1. Faculty of Materials Science and Engineering,
Kunming University of Science and Technology, Kunming 650093, China;
2. Research Center for Analysis and Measurement,
Kunming University of Science and Technology, Kunming 650093, China）
Abstract:The uniaxial compressive deformation experiments on ZCuSn10 copper alloy billet with different original semi-solid organizations prepared by strain induced melt activation (SIMA) process were carried out using Gleeble-1500 thermo-mechanical simulator. The effect of pre-deformation and compressive deformation conditions on true strain–stress curves and organizations of semi-solid billet were analyzed. And the liquid flowing law was studied by analyzing the macroscopic morphology and microstructure of ZCuSn10 copper alloy after the compression. The results show that deformation resistance reduces with increasing the pre-deformation amount and deformation temperature. The deformation temperature of uniaxial compression has a greater impact on the peak stress of semi-solid ZCuSn10 copper alloy during uniaxial compression, but has a less impact on steady stress. As same as the compressive deformation of solid metal, there are three typical compression areas in semi-solid ZCuSn10 copper alloy during uniaxial compression, namely difficult deformation zone (zone Ⅰ), large deformation zone (zone Ⅱ)and free deformation zone (zone Ⅲ). The contents of liquid phase in zones Ⅰ, Ⅱ and Ⅲ are 15.23%, 5.31% and 20.12%, respectively. And the liquid phase flowing occurs among different deformation zones, a small amount of liquid phase in the difficult deformation zone flows to the large degree deformation zone, and a large amount of liquid phase in the large degree deformation zone flows to the free deformation zone.
Key words: ZCuSn10 copper alloy; semi-solid; uniaxial compression; deformation behavior
