(1. 重慶大學 材料科學與工程學院，重慶 400044；
2. 國家鎂合金材料工程技術研究中心，重慶 400045)
摘 要: 采用Gleeble-1500熱/力模擬試驗機進行壓縮實驗，研究Mg-2Zn-1Mn (ZM21)與Mg-6Zn-1Mn (ZM61)合金在變形溫度523~723 K、應變速率0.01~10 s-1范圍內的流變應力行為，并以熱壓縮實驗為基礎，建立兩種合金的動態模型加工圖，引入材料加工硬化率θ，結合θ—σ曲線拐點判據識別合金發生動態再結晶的臨界應變?chǔ)?SUB>c。結果表明，ZM21與ZM61合金在熱壓縮過程中發生明顯的動態回復與動態再結晶；隨著Zn含量的增加，ZM61合金的變形激活能比ZM21合金的升高約20%，并且ZM61合金在高溫變形時更容易出現失衡；兩者發生動態再結晶的臨界應變?chǔ)?SUB>c均隨著應變速率的增加而升高，隨變形溫度的升高而降低。
關鍵字: 鎂合金；熱壓縮；動態再結晶；臨界應變
（1. College of Materials Science and Engineering, Chongqing University, Chongqing 400044, China;
2. National Engineering Research Center for Magnesium Alloys, Chongqing 400045, China）
Abstract:The thermal compression behavior of Mg-2Zn-1Mn (ZM21) and Mg-6Zn-1Mn (ZM61) magnesium alloys was investigated by uniaxial compression tests on Gleeble-1500 thermal simulation test machine at the temperature ranging from 523 K to 723 K and strain rate ranging from 0.01 s-1 to 10 s-1. According to the experimental results, the hot processing maps based on the dynamic materials modeling were drawn. The critical strain εc that the dynamical recrystallization occurs was identified by introducing the hard working rate θ and inflection point of θ—σ curves under different deformation. The results show that the dynamic recovery and dynamic recrystallization occur obviously during hot compression of ZM21and ZM61 alloys. Compared with ZM21 alloy, the deformation activation energy of ZM61 alloy increases by 20% because of the increase of Zn content, and the ZM61 alloy is more unstable than ZM21 alloy. The critical strain εc of both alloys increases with the increase of strain rate and decreases with the increase of deformation temperature.
Key words: magnesium alloy; thermal compression; dynamic recrystallization; critical strain
