(1. 沈陽工業大學 材料科學與工程學院，沈陽 110023；
2. 沈陽化工學院 機械工程學院，沈陽 110142)
摘 要: 通過蠕變性能測試及組織形貌觀察，研究不同形態孔洞缺陷對單晶鎳基合金蠕變性能的影響，針對合金中存在有/無裂紋孔洞等鑄造缺陷，對高溫蠕變期間近有/無孔洞區域的應力分布進行有限元分析，根據拉應力載荷下近孔洞區域的微觀應力分布特性，分析不同形態孔洞區域應力分布對單晶合金蠕變行為及組織演化的影響。結果表明：在高溫蠕變期間，近有/無裂紋孔洞區域的應力分布對合金中γ¢相筏形化的形態有明顯影響，在有/無裂紋孔洞兩側極點處，存在最大應力值，且可致使其裂紋沿垂直于應力軸方向發生萌生與擴展；與無裂紋孔洞相比，在有裂紋孔洞兩側的極點處應力值較大，隨著蠕變的進行，在較大應力處易于發生裂紋的擴展是合金具有較低蠕變壽命的主要原因。
關鍵字: 單晶；鎳基合金；孔洞形態；有限元分析；應力分布；蠕變壽命
single crystal nickel-base superalloy
（1. School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110023, China;
2. School of Mechanical Engineering, Shenyang Institute of Chemical Technology, Shenyang 110142, China）
Abstract:By means of creep properties measurement and microstructure observation, the influence of cavity morphology on the creep behaviors of a single crystal nickel-base alloy was investigated. Due to the cavity with or without cracks exists in the as-cast superalloy, the stress distribution near the cavity with or without cracks during high temperature creep was analyzed by finite elements analysis method (FEM), and the influence of the stress distribution near the cavity regions on the creep behaviors and microstructure evolution of the superalloy was discussed according to the feature of the stress distribution near the cavity. The results show that, during high temperature creep, the stress distribution near the cavity with or without cracks has an obvious effect on the morphology of the rafted γ¢ phase in the superalloy, the maximum stress value which appears in two sides of the cavity with or without cracks may promote the initiation and propagation of the cracks along the direction vertical to the applied stress axis. Compared with the crack-free cavity, the bigger stress value appears in two sides of the cavity with cracks which propagates easily as creep goes on, this is the main reason resulting in the alloy with shorter creep lifetime.
Key words: single crystal; nickel-based superalloys; cavity morphology; FEM analysis; stress distribution; creep lifetime
